ABB 1SAP124100R0172 (PM5052-R-ETH): engineering decision notes
The full ABB 1SAP124100R0172 order code identifies the PM5052-R-ETH version to review. Use the questions below to distinguish the specified unit from a visually similar part before procurement.
Technical data at a glance
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | 1SAP124100R0172 |
| Product family | PM5052-R-ETH |
| Component role | AC500-eCo V3 PLC with relay outputs |
| Full order code | 1SAP124100R0172 |
| ABB type | PM5052-R-ETH |
| Memory | 4 MB |
| Inputs | 12 digital inputs at 24 V DC |
| Outputs | Six relay outputs plus two 24 V DC configurable points |
| Network | Ethernet; three option slots |
| Related | 1SAP124600R0173 uses transistor outputs, two Ethernet ports and 18 MB; not interchangeable |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
The ABB 1SAP124100R0172 values shown here come from the cited manufacturer specification where stated. Confirm project-specific options and the delivered label before installation.
What interfaces require confirmation?
Trace each ABB 1SAP124100R0172 supply, terminal and communications connection against the as-built schematic. Record cable type, terminal map, connector orientation and any controller configuration.
If ABB 1SAP124100R0172 is a networked or programmable unit, verify project file, firmware, addresses and protocol support. If it is an electrical accessory, confirm its load and mounting coordination.
What duty is this code being asked to perform?
ABB 1SAP124100R0172 is intended to run the relay-output version of an AC500-eCo V3 program. Start with the machine or panel drawing and identify the exact point where this function is required.
A replacement request for ABB 1SAP124100R0172 should include the reason for change: failed hardware, planned upgrade, missing accessory or renewed safety validation. Each reason has a different acceptance threshold.
Which designation and host must match?
Write ABB 1SAP124100R0172 in full on the order, along with type PM5052-R-ETH. Compare the installed marking, hardware revision and host equipment rather than relying on the short family name.
For ABB 1SAP124100R0172, check output load type, option boards, project firmware, memory and Ethernet topology. Similar modules may differ by I/O mix, network role, contact technology, environmental variant or package quantity.
What must be saved before the change?
Before touching ABB 1SAP124100R0172, apply the site's isolation and stored-energy rules. Save the original configuration, parameter image or wiring evidence where the device is programmable.
Label every ABB 1SAP124100R0172 lead and take photographs of the installed assembly. Protect spare contacts and module pins from damage; preserve the removed part until acceptance is signed.
What test demonstrates correct operation?
With ABB 1SAP124100R0172 installed under the approved procedure, test each I/O point, network service and controlled start-up. Record the pre-test state, expected response and measured result.
For ABB 1SAP124100R0172, include negative or fault-path checks when the function is protective, safety-related or communications-critical. Sign off the test only after normal operation and diagnostics agree.
How is the delivered item checked?
Inspect the ABB 1SAP124100R0172 package, article label and revision at goods receipt. Check the included terminal units, accessories and any license status against the approved purchase specification.
Do not substitute a neighboring ABB 1SAP124100R0172 family code solely because the housing looks alike. Escalate any discrepancy to the site's engineering owner before the maintenance window.
What evidence should stay with the asset?
Store the ABB 1SAP124100R0172 purchase code, delivered label, configuration, firmware and test evidence in the asset record. This prevents later maintenance from relying on an abbreviated description.
A future enquiry for ABB 1SAP124100R0172 should use the validated record and ask the supplier to disclose any change of article, option, packaging or product life-cycle status.
How do related codes differ?
These PM5052-R-ETH references are grouped under ABB 1SAP124100R0172 for comparison, not as direct substitutes. Confirm the particular output, I/O or environmental difference for each complete designation.
- 1SAP124600R0173
Three-point release record
- Confirm the complete ABB 1SAP124100R0172 article and host fit.
- Record the ABB 1SAP124100R0172 configuration and installation checks.
- Witness the ABB 1SAP124100R0172 functional acceptance test.
Keep the ABB 1SAP124100R0172 manufacturer reference and signed field result with the installed asset.
