ACH580-01-025A-4+B056+J400: HVAC load and option matching
ABB ACH580-01-025A-4+B056+J400 belongs to the ACH580 HVAC drive family. ABB's ACH580-01 rating table gives 25 A and 11 kW at the 400 V reference condition for the 025A-4 size, with R2 frame designation.
Technical data for identification
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | ACH580-01-025A-4+B056+J400 |
| Application family | ABB ACH580 HVAC drive |
| Nominal power at 400 V | 11 kW |
| Nominal output current | 25 A |
| Frame | R2 at published 400 V rating |
| Supply | Three-phase 380–415 V at 400 V table conditions |
| Option review | Check B056 enclosure and J400 panel against order record |
For a drive or softstarter, compare the motor nameplate, overload profile, upstream protection, cabling, heat rejection and stop category with the actual machine. The installation drawing and the fitted option codes govern the final selection.
Field checks and acceptance
Commissioning of ACH580-01-025A-4+B056+J400 should follow a controlled procedure. Back up the HVAC parameters and trend information, verify wiring and airflow around the drive, and commission the control sequence from both local and remote sources. Test sensor loss, alarm reporting, motor direction and the defined safe operating state.
Capture the as-left settings, test points, abnormal-state response and revision of ACH580-01-025A-4+B056+J400. Include photographs of its nameplate and terminal arrangement so the next service event can be traced.
Where this configuration fits
ACH580-01-025A-4+B056+J400 should be assessed in the actual equipment arrangement. A fan or pump application needs motor-current comparison across the actual speed range, minimum-speed restrictions, bearing and acoustic considerations, and a clear fire or smoke-control interface where relevant. Evaluate the building-management system's command and feedback sequence.
A request for ACH580-01-025A-4+B056+J400 should identify the host system, process or motor duty, available supply and the expected normal and fault behavior. This makes the selection review specific to the installed equipment.
Order-code and compatibility review
For ACH580-01-025A-4+B056+J400, Confirm the enclosure and panel option codes from the ordered configuration, alongside BACnet or other communications hardware, I/O availability, filters, disconnects and bypass arrangement. A look-alike ACH580 suffix may not provide the same cabinet interface.
Before substituting ACH580-01-025A-4+B056+J400, compare the complete label with the engineering drawing, ABB configuration data, installed accessories and site approval record. A partial designation or a similar enclosure cannot establish interchangeability.
Related configuration references
The following ACH580-01-025A-4+B056+J400 family references are identification aids. Ratings, options and approvals can differ; each complete designation needs its own review.
- ACH580-01-026A-4+B056
- ACH580-01-032A-4+B056
- ACH580-01-062A-4
- ACH580-01-073A-4
- ACH580-01-073A-4+B056
- ACH580-01-12A6-4+B056+J400
Information to send with a replacement inquiry
Provide the exact model ACH580-01-025A-4+B056+J400, quantity, serial or revision, application conditions, required connection and approval, and a legible nameplate photograph. Ask for confirmation of accessories and any approved successor.
Keep ACH580-01-025A-4+B056+J400 in the asset register and maintenance record as the exact search phrase. Record who approved the selected device, what was tested and whether the installed configuration differs from the base family specification.
Final engineering decision
Approve ACH580-01-025A-4+B056+J400 only when the verified ratings and ordered options match the equipment record. Resolve every discrepancy in code, connection, supply, firmware or process limit before energizing the system.
The published family values for ACH580-01-025A-4+B056+J400 support identification and initial selection. The device nameplate, matching ABB instructions and the site's approved design determine final suitability.
