Pepperl+Fuchs KLD2-FBPS-1.25.360: function, connections and handover
Pepperl+Fuchs KLD2-FBPS-1.25.360 is a FieldConnex fieldbus power supply selected to provide conditioned power to a fieldbus segment. The full KLD2-FBPS-1.25.360 code is the identification anchor for this page. The shared main montage illustrates the Pepperl+Fuchs category and is not a photograph of this exact option. Before using KLD2-FBPS-1.25.360 as a spare, compare the installed label and project drawing with the current manufacturer documentation.
Technical specification and identity
| Technical item | Verified value / selection note |
|---|---|
| Exact model | KLD2-FBPS-1.25.360 |
| Product role | FieldConnex fieldbus power supply |
| Function | Fieldbus segment power supply |
| Series | FieldConnex KLD2-FBPS |
| Variant | 1.25.360 exact designation |
| Approval | Confirm the installed certificate and installation category |
| Variant check | Confirm the complete designation and current manufacturer documentation before replacement. |
Before the change
For installation of KLD2-FBPS-1.25.360, document the existing assembly before disturbing it. Photograph the full label, terminals, cable exits, brackets and adjacent modules; mark conductors and save any controller or software configuration. Compare voltage, polarity, loading and environmental limits against the exact KLD2-FBPS-1.25.360 technical record. If KLD2-FBPS-1.25.360 is part of a safety or hazardous-area circuit, the site-approved design and certificates take precedence over an appearance match.
Start with the real duty of KLD2-FBPS-1.25.360: provide conditioned power to a fieldbus segment. Then trace what connects to KLD2-FBPS-1.25.360, including its power source, input or target, outgoing signal and mechanical support. Check segment load, trunk termination and the relevant hazardous-area design. Record the actual site settings and the parts that are supplied separately. This matters because a near-identical type string can conceal a different output, connection, dimension or approval.
At commissioning
After fitting KLD2-FBPS-1.25.360, prove its function in the completed system, not merely its power-on indication. Apply a known field condition, read the downstream controller or diagnostic tool, and repeat at both normal and limiting conditions. For KLD2-FBPS-1.25.360, check segment load, trunk termination and the relevant hazardous-area design. Capture the observed readings, alarm states and any parameter changes so the maintenance record explains why KLD2-FBPS-1.25.360 was accepted.
At purchasing handoff
When asking for KLD2-FBPS-1.25.360, include the entire type code, quantity, installation location, applicable approval, mating connector or board and required accessories. Ask a supplier to confirm the exact KLD2-FBPS-1.25.360 designation in writing. A proposed equivalent must be checked independently for electrical behavior, mounting, software and certifications. The related codes below are search and identification references; they are not a declaration that they interchange with KLD2-FBPS-1.25.360.
Related-looking designations
The following strings resemble KLD2-FBPS-1.25.360 in the supplied product family. Their full suffixes may change function, ratings, mechanical fit or approval; consult each exact manufacturer's record before a substitute is used.
- KLD2-GT-DPR.4PA
- KLD2-PC-1.1.IEC
- KLD2-PL-1.PA
- KLD2-PR-1.IEC
- KLD2-PR-EX1.1EC1
- KLD2-PR-EX1.IEC1
Close-out note
For future service of KLD2-FBPS-1.25.360, retain the final wiring diagram, settings, test result and replacement reference together. Recheck the data for KLD2-FBPS-1.25.360 if the connected controller, process conditions or regulatory setting changes. The table describes the named KLD2-FBPS-1.25.360 where a value is stated; do not extend those values automatically to another listed code.
