NCN25-F35-A2-250-15M-V1 selection notes for the field connection, operating limits and service handover
Pepperl+Fuchs NCN25-F35-A2-250-15M-V1 is a flat-pack inductive proximity sensor used for position detection where a broad sensing face is needed. This page identifies the representative designation and the checks that matter when the device is selected for a real installation. The common product montage is a category reference image, not a photograph of the exact NCN25-F35-A2-250-15M-V1 unit. Compare the full label and current manufacturer data before committing a purchase or changing a live circuit.
Key technical data
| Technical item | Verified value / selection note |
|---|---|
| Exact designation | NCN25-F35-A2-250-15M-V1 |
| Product type | flat-pack inductive proximity sensor |
| Rated sensing distance | 25 mm; assured distance 0 to 20 mm |
| Installation | Flush mountable |
| Electrical form | 4-wire DC output |
| Operating supply | 10 to 30 V DC |
| Variant boundary | Use the complete type code and current device label when selecting a replacement. |
Selection checkpoint: identify the complete NCN25-F35-A2-250-15M-V1 code before comparing its field interface with an installed unit.
Interface and installation fit
For NCN25-F35-A2-250-15M-V1, Compare the F35 housing, sensing face orientation, mounting metal and the complete A2-250-15M-V1 termination. Review the mating equipment, supply path, mounting space, cable or terminal assignment and any required hazardous-area documentation. If the present installation has field-modified wiring or programming, photograph and record it before removal. The same-looking item can require different wiring or settings.
Operating role and application
In the intended system, NCN25-F35-A2-250-15M-V1 is used for position detection where a broad sensing face is needed. Its role is not defined by the product picture or a shared prefix alone. Establish what arrives at the device, what leaves it and which controller, field instrument or mechanical component it must match. When NCN25-F35-A2-250-15M-V1 is ordered as a spare, preserve the complete suffix and all installed configuration information.
Procurement and replacement details
When requesting NCN25-F35-A2-250-15M-V1, Supply a photo of the installed label and connector plus the target material; do not substitute a 25 mm code by distance alone. State operating environment, required certificates and the exact application. Request written confirmation for any proposed alternative. A reference model in the list below may belong to the same visible naming cluster but is not a default functional replacement for NCN25-F35-A2-250-15M-V1.
Commissioning and maintenance
After fitting NCN25-F35-A2-250-15M-V1, Verify both switch states at the machine's minimum and maximum operating gap. Record both the expected and observed behavior. Inspect indicators, fault response and controller diagnostics where provided. If the test does not match, verify wiring, configuration and connected equipment before assuming that a new NCN25-F35-A2-250-15M-V1 is defective.
Related designation references
The following catalog designations share the visible NCN naming cluster with NCN25-F35-A2-250-15M-V1. They are grouped to aid search and procurement, not to assert identical ratings, wiring, approvals or interchangeability. Each complete code must be checked separately against the required duty.
- NCN15-30GM40-N0-20M
- NCN25-F35-A2-250-V1
- NCN25-F35-A2-250-V1 187479
- NCN3-F25-N4-5M
- NCN3-F25-N4-V1
- NCN3-F31K-N4
- NCN4-12GM35-N0
- NCN4-12GM35-N0-10M
- NCN4-12GM35-N0-5M
- NCN4-12GM35-NO-V1
- NCN4-12GM40-Z0-V1
- NCN4-12GM40-Z1
- NCN40-L2-N0-V1
- NCN40-L2-NO-V1
- NCN50-FP-A2-P1
- NCN50-FP-N0-P1
- NCN50-FP-Z2-P1
- NCN5O-FP-NO-P1
- NCN8-18GM40-N0
- NCN8-18GM40-N0-5M
- NCN8-18GM40-NO-5M
- NCN8-18GM40-Z1
Final selection check
For NCN25-F35-A2-250-15M-V1, confirm the latest datasheet and nameplate before ordering or commissioning. Retain the loop drawing, configuration and acceptance record with the maintenance file. The technical values above apply to NCN25-F35-A2-250-15M-V1 only where stated, not to every related designation.
