BASIC INFO
Production overviews
MTL 4500 Intrinsically Safe Isolators MTL4523
MTL4532 – MTL5532 PULSE ISOLATOR pulse & 4/20mA current outputs The MTLx532 isolates pulses from a switch, proximity detector, current pulse transmitter or voltage pulse transmitter located in a hazardous area. It is ideal for applications involving high pulse rates and fast response times, by repeating the pulses into the safe area. An analogue output proportional to frequency is also provided, together with a relay output, which may be configured to act as an alarm. Configuration is carried out with a personal computer.
MTL4523 safe isolator product specification
SPECIFICATION
See also common specification
Number of channels
One, fully floating
Sensor type
Switch or proximity detector (NAMUR/BS EN 60947–5–6:2001)
2– or 3–wire voltage or pulse transmitter
Location of switch
Zone 0, IIC, T6 hazardous area
Div. 1, Group A, hazardous location
Location of proximity detector or transmitter
Zone 0, IIC, T4–T6 if suitably certified
Div.1, Group A, hazardous location
Input
Switch input:
Output ON if switch is closed
Proximity detector input:
Excitation: 7.0 to 9.0V dc from 1kΩ nominal
Output ON if input > 2.1mA* (< 2kΩ)
Output OFF if input < 1.2mA* (> 10kΩ)
Switching hysteresis: 0.2mA (650Ω) nominal
*NAMUR and BS EN 60947–5–6:2001standards
Current pulse input:
Transmitter supply: 16.5V dc at 20mA
Short circuit current: 24mA
Output: Iin > 9.0mA = ON, Iin < 7.0mA = OFF
Switching hysteresis: 0.5mA
Voltage pulse input
Input impedance: > 10kΩ
Switching point voltage (Vsp): 3, 6, or 12V nominal
(User selectable by switches on the side of the module)
Output: Vin > Vsp = ON, Vin < Vsp = OFF
Switching hysteresis: 100mV + (0.1 x Vsp) typical
Safe-area pulse output
Maximum delay: 10µs
Maximum off–state voltage: 35V
Maximum off–state leakage current: 10µA
Maximum on–state resistance: 25Ω
Maximum on–state current: 50mA
Output OFF if supply fails
Note: LFD signal is Zener-diode protected against inductive loads
Safe-area current output
Input capture delay: 2 signal periods (5ms min.)
Signal range: 4 to 20mA
Under/over range: 0 to 22mA
Load resistance: 0 to 450Ω @20mA
Output resistance: >1MΩ
Ripple: < 50µA peak-to-peak
Accuracy: better than 20µA at 20°C
Temperature drift: < 1µA/°C
Risetime (10% - 90%, after step change): 60 ms
Alarm output
Relay ON in alarm, 0.5A @ 35Vdc max.
Pulse width
High: 10µs min
Low: 10µs min
Frequency range
0 – 50kHz - pulse output mode
0 – 10KHz - for analogue output
LED indicators
Green: power indication
Yellow: on when output circuit is on
Red: flashing when line fault or error
Power requirement
65mA at 24V dc
70mA at 20V dc
55mA at 35V dc
Power dissipation within unit
1.35W maximum at 24V
1.75W maximum at 35V
Safety description (Um = 253V rms or dc)
Terminals 2 to 1 and 6 to 1
Uo=10.5V Io=14mA Po=37mW
Terminals 4 to 3 and 1
Uo=28V Io=93mA Po=651mW
Terminals 3 to 1
Non-energy-storing apparatus ≤1.5V, ≤0.1A and ≤25mW; can be
connected without further certification into any IS loop with an opencircuit
voltage <28V
Terminals 5 to 4 and 1
Vmax ≤ 28V, Imax ≤ 94mA, Pmax ≤ 0.66W
Configurator
A personal computer running MTL PCS45 software with a
PCL45USB serial interface.
Other related product models for MTL4500 range series as below.
MTL4501-SR
MTL4504
MTL4510
MTL4510B
MTL4511
MTL4513
MTL4514D
MTL4514_B
MTL4516
MTL4516C
MTL4517
MTL4521
MTL4521L
MTL4523
MTL4523L
MTL4523R
MTL4523V-VL
MTL4524
MTL4524S
MTL4525
MTL4526
MTL4541
MTL4541A
MTL4541AS
MTL4541B
MTL4541P
MTL4541S
MTL4541T
MTL4544
MTL4544A
MTL4544AS
MTL4544B
MTL4544D
MTL4544S
MTL4546
MTL4546C
MTL4546S
MTL4546Y
MTL4549
MTL4549C
MTL4549Y
MTL4573
MTL4575
MTL4576-RTD
MTL4576-THC
MTL4581
MTL4582B
MTL4531
MTL4532
MTL4561
MTL4599
MTL4599N
For more information about MTL4523 safe isolators, please feel free to send me an inquiry here.
Contact details
HONGKONG XIEYUAN TECH CO., LIMITED
Telephone:86-027-85880977
Mobile :86-13545206420(Whatapp&Wechat is available)
Fax:86-027-85309780
Skype:Diana@hkxytech.com
E-mail:Diana@hkxytech.com Or Cc:Dianatian118@gmail.com
Website:www.hkxy-lowvoltage.com
MTL4532 – MTL5532 PULSE ISOLATOR pulse & 4/20mA current outputs The MTLx532 isolates pulses from a switch, proximity detector, current pulse transmitter or voltage pulse transmitter located in a hazardous area. It is ideal for applications involving high pulse rates and fast response times, by repeating the pulses into the safe area. An analogue output proportional to frequency is also provided, together with a relay output, which may be configured to act as an alarm. Configuration is carried out with a personal computer.
MTL4523 safe isolator product specification
SPECIFICATION
See also common specification
Number of channels
One, fully floating
Sensor type
Switch or proximity detector (NAMUR/BS EN 60947–5–6:2001)
2– or 3–wire voltage or pulse transmitter
Location of switch
Zone 0, IIC, T6 hazardous area
Div. 1, Group A, hazardous location
Location of proximity detector or transmitter
Zone 0, IIC, T4–T6 if suitably certified
Div.1, Group A, hazardous location
Input
Switch input:
Output ON if switch is closed
Proximity detector input:
Excitation: 7.0 to 9.0V dc from 1kΩ nominal
Output ON if input > 2.1mA* (< 2kΩ)
Output OFF if input < 1.2mA* (> 10kΩ)
Switching hysteresis: 0.2mA (650Ω) nominal
*NAMUR and BS EN 60947–5–6:2001standards
Current pulse input:
Transmitter supply: 16.5V dc at 20mA
Short circuit current: 24mA
Output: Iin > 9.0mA = ON, Iin < 7.0mA = OFF
Switching hysteresis: 0.5mA
Voltage pulse input
Input impedance: > 10kΩ
Switching point voltage (Vsp): 3, 6, or 12V nominal
(User selectable by switches on the side of the module)
Output: Vin > Vsp = ON, Vin < Vsp = OFF
Switching hysteresis: 100mV + (0.1 x Vsp) typical
Safe-area pulse output
Maximum delay: 10µs
Maximum off–state voltage: 35V
Maximum off–state leakage current: 10µA
Maximum on–state resistance: 25Ω
Maximum on–state current: 50mA
Output OFF if supply fails
Note: LFD signal is Zener-diode protected against inductive loads
Safe-area current output
Input capture delay: 2 signal periods (5ms min.)
Signal range: 4 to 20mA
Under/over range: 0 to 22mA
Load resistance: 0 to 450Ω @20mA
Output resistance: >1MΩ
Ripple: < 50µA peak-to-peak
Accuracy: better than 20µA at 20°C
Temperature drift: < 1µA/°C
Risetime (10% - 90%, after step change): 60 ms
Alarm output
Relay ON in alarm, 0.5A @ 35Vdc max.
Pulse width
High: 10µs min
Low: 10µs min
Frequency range
0 – 50kHz - pulse output mode
0 – 10KHz - for analogue output
LED indicators
Green: power indication
Yellow: on when output circuit is on
Red: flashing when line fault or error
Power requirement
65mA at 24V dc
70mA at 20V dc
55mA at 35V dc
Power dissipation within unit
1.35W maximum at 24V
1.75W maximum at 35V
Safety description (Um = 253V rms or dc)
Terminals 2 to 1 and 6 to 1
Uo=10.5V Io=14mA Po=37mW
Terminals 4 to 3 and 1
Uo=28V Io=93mA Po=651mW
Terminals 3 to 1
Non-energy-storing apparatus ≤1.5V, ≤0.1A and ≤25mW; can be
connected without further certification into any IS loop with an opencircuit
voltage <28V
Terminals 5 to 4 and 1
Vmax ≤ 28V, Imax ≤ 94mA, Pmax ≤ 0.66W
Configurator
A personal computer running MTL PCS45 software with a
PCL45USB serial interface.
Other related product models for MTL4500 range series as below.
MTL4501-SR
MTL4504
MTL4510
MTL4510B
MTL4511
MTL4513
MTL4514D
MTL4514_B
MTL4516
MTL4516C
MTL4517
MTL4521
MTL4521L
MTL4523
MTL4523L
MTL4523R
MTL4523V-VL
MTL4524
MTL4524S
MTL4525
MTL4526
MTL4541
MTL4541A
MTL4541AS
MTL4541B
MTL4541P
MTL4541S
MTL4541T
MTL4544
MTL4544A
MTL4544AS
MTL4544B
MTL4544D
MTL4544S
MTL4546
MTL4546C
MTL4546S
MTL4546Y
MTL4549
MTL4549C
MTL4549Y
MTL4573
MTL4575
MTL4576-RTD
MTL4576-THC
MTL4581
MTL4582B
MTL4531
MTL4532
MTL4561
MTL4599
MTL4599N
For more information about MTL4523 safe isolators, please feel free to send me an inquiry here.
Contact details
HONGKONG XIEYUAN TECH CO., LIMITED
Telephone:86-027-85880977
Mobile :86-13545206420(Whatapp&Wechat is available)
Fax:86-027-85309780
Skype:Diana@hkxytech.com
E-mail:Diana@hkxytech.com Or Cc:Dianatian118@gmail.com
Website:www.hkxy-lowvoltage.com
