How ABB 1SFA899300R1008 fits the approved assembly
ABB 1SFA899300R1008 is the identified communication option module for the softstarter communication module options application. The shared product-category image is a reference, not a photograph certifying the exact ABB 1SFA899300R1008 configuration.
The ABB 1SFA899300R1008 technical table separates manufacturer-stated identity from the installation checks that depend on the particular host device.
Key technical data and selection notes
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | 1SFA899300R1008 |
| Product family | softstarter communication module options |
| Component role | communication option module |
| Exact ABB order reference | 1SFA899300R1008 |
| ABB product series | softstarter communication module options |
| ABB order code | 1SFA899300R1008 |
| Manufacturer designation | AB-MODBUS-TCP-2 |
| Representative | AB-MODBUS-TCP-2 communication module |
| Related designation | PS-MBIA communication module |
| Boundary | Verify actual host, protocol and firmware for each code |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
At-a-glance procurement checks
- Confirm the complete ABB 1SFA899300R1008 order code and package marking.
- Match ABB 1SFA899300R1008 to the host, drawings and approved accessory position.
- Record the required electrical or mechanical limits before fitting ABB 1SFA899300R1008.
Installed-system role
ABB 1SFA899300R1008 is intended to connect the approved starter communication interface. Identify its place in the circuit before comparing visually similar accessories.
A manufacturer family prefix does not prove that ABB 1SFA899300R1008 has the same contact count, supply, pole arrangement or software interface as another listed option.
Receiving and storage
When ABB 1SFA899300R1008 arrives, compare the carton, device marking and purchase record. Inspect terminals, release mechanisms, molded parts and accessory contents as applicable.
Keep ABB 1SFA899300R1008 isolated from usable stock if its code or condition differs. Resolve the discrepancy before the scheduled shutdown.
Compatibility evidence
For ABB 1SFA899300R1008, check host starter, module protocol, network project and firmware. Retain the host label, order code and drawing revision used for the decision.
If a substitute is proposed for ABB 1SFA899300R1008, require a documented comparison of every changed terminal, rating, supplied piece and approved host.
Safe installation
Isolate and verify all applicable energy sources before installing ABB 1SFA899300R1008. Follow ABB and site requirements for lockout, stored energy and breaker operating springs.
Record wiring and orientation before removing the old unit. Install ABB 1SFA899300R1008 with the approved mounting and recheck protective covers and clearances.
Future purchase boundary
Keep ABB 1SFA899300R1008 and its exact host in the maintenance register. Include any pole, voltage, feature or option restriction beside the stock record.
For later ABB 1SFA899300R1008 enquiries, use the full code and verified installation evidence rather than a shortened series name.
Commissioning record
After installing ABB 1SFA899300R1008, prove configured communication and diagnostics. Test normal operation and the relevant inhibited or fault state under an authorized procedure.
Archive ABB 1SFA899300R1008 as-left identity, settings, results and sign-off. An indicator or mechanical fit alone does not establish full circuit acceptance.
Other ABB order codes in this series
These ABB codes are represented by the ABB 1SFA899300R1008 page rather than published separately. They can differ in supply, features, contact arrangement or fit; they are not automatic substitutes.
- 1SFA899300R1020
Procurement handover
State ABB 1SFA899300R1008, quantity and host equipment on the purchase request.
File the ABB 1SFA899300R1008 delivery identity and acceptance test in the equipment history.
