ABB OT315E03 1SCA022727R5910 selection decision record
Start the ABB OT315E03 1SCA022727R5910 enquiry with a precise equipment identity and a defined plant function. The verified values below establish a technical baseline; they do not replace checking the delivered unit.
Verified parameters and fit limits
| Technical item | Verified value / selection note |
|---|---|
| Complete designation | OT315E03 1SCA022727R5910 |
| Product family | OT315E03 |
| Component role | 315 A three-pole switch-disconnector |
| Type | OT315E03 |
| Order code | 1SCA022727R5910 |
| Poles | 3 |
| Rated current | 315 A |
| Mounting | Base mount, front operated |
| Handle/shaft | Not included |
| Final configuration | Confirm exact nameplate, hardware revision and order options before purchase |
Before signing off OT315E03 1SCA022727R5910, check the current ABB documentation and the actual nameplate. Family-level information must not be used as a guaranteed option for every configuration.
What problem does it solve?
ABB OT315E03 1SCA022727R5910 is selected to isolate the designed three-phase feeder. State the actual circuit, loop or motor tag and the operating problem before deciding on a replacement.
A request for OT315E03 1SCA022727R5910 without site duty, installed revision or failure evidence can lead to a technically different part being offered.
Which interfaces must match?
For OT315E03 1SCA022727R5910, confirm fuse/breaker coordination, busbar space and handle. Compare the original label, mounting, field terminals and power/control supplies with the ABB product reference.
Keep the OT315E03 1SCA022727R5910 electrical or network interface unchanged unless engineering has approved the revised drawing, settings and test scope.
What changes at installation?
Installing OT315E03 1SCA022727R5910 may affect adjacent wiring, panel access and auxiliary accessories. Check clearance and isolate the correct energy sources under the site's permit system.
Before disturbing OT315E03 1SCA022727R5910, save photos, configuration, parameter values and an alarm baseline. Keep removed parts identifiable until acceptance is signed.
What can cause a poor match?
A OT315E03 1SCA022727R5910 suffix or order-code difference may identify another coil, contact set, protocol, release, shaft or voltage. A matching appearance is not interchangeability evidence.
If the supplied OT315E03 1SCA022727R5910 differs from the approved item, quarantine it for review rather than changing field wiring to make it fit.
How is performance proved?
After approved installation of OT315E03 1SCA022727R5910, verify isolation and mechanical travel. Use only documented safe test methods and include connected equipment behavior.
Record the OT315E03 1SCA022727R5910 as-left results, asset tag, revision, date and witness. Restore alarms, interlocks and normal control before service handover.
What should purchasing retain?
The ABB OT315E03 1SCA022727R5910 record should include the complete designation, required accessories, label evidence and the current installation manual revision.
For any proposed substitute to OT315E03 1SCA022727R5910, obtain written confirmation of every changed technical characteristic and the site's acceptance.
Other codes in this same series
The following OT315E03 references can accompany an ABB OT315E03 1SCA022727R5910 enquiry. Suffix changes can affect ratings, fit or approvals, so none is an automatic replacement.
No other unassigned OT315E03 reference is grouped with OT315E03 1SCA022727R5910 in this release.
Enquiry and acceptance handoff
Quote ABB OT315E03 1SCA022727R5910 exactly, include the asset tag and duty, and request confirmation of any missing accessories or alternative build.
Keep the approved OT315E03 1SCA022727R5910 comparison, installation checks and test results in the maintenance record.
