Technical identity and on-site decisions for TCP-LBF-IA1.36.IE.0
Pepperl+Fuchs TCP-LBF-IA1.36.IE.0 is a fieldbus surge protector selected to protect a fieldbus connection from transient surges. The full TCP-LBF-IA1.36.IE.0 code is the identification anchor for this page. The shared main montage illustrates the Pepperl+Fuchs category and is not a photograph of this exact option. Before using TCP-LBF-IA1.36.IE.0 as a spare, compare the installed label and project drawing with the current manufacturer documentation.
Technical specification and identity
| Technical item | Verified value / selection note |
|---|---|
| Exact model | TCP-LBF-IA1.36.IE.0 |
| Product role | fieldbus surge protector |
| Function | Fieldbus surge protection |
| Diagnostic option | IE.0 without diagnosis |
| Installation | Check T-connector and terminator separately |
| Approval | Verify installed Ex and system documentation |
| Variant check | Confirm the complete designation and current manufacturer documentation before replacement. |
Application decision
Start with the real duty of TCP-LBF-IA1.36.IE.0: protect a fieldbus connection from transient surges. Then trace what connects to TCP-LBF-IA1.36.IE.0, including its power source, input or target, outgoing signal and mechanical support. Confirm the compatible coupler, earthing and segment protection design. Record the actual site settings and the parts that are supplied separately. This matters because a near-identical type string can conceal a different output, connection, dimension or approval.
Pre-installation record
For installation of TCP-LBF-IA1.36.IE.0, document the existing assembly before disturbing it. Photograph the full label, terminals, cable exits, brackets and adjacent modules; mark conductors and save any controller or software configuration. Compare voltage, polarity, loading and environmental limits against the exact TCP-LBF-IA1.36.IE.0 technical record. If TCP-LBF-IA1.36.IE.0 is part of a safety or hazardous-area circuit, the site-approved design and certificates take precedence over an appearance match.
Acceptance sequence
After fitting TCP-LBF-IA1.36.IE.0, prove its function in the completed system, not merely its power-on indication. Apply a known field condition, read the downstream controller or diagnostic tool, and repeat at both normal and limiting conditions. For TCP-LBF-IA1.36.IE.0, confirm the compatible coupler, earthing and segment protection design. Capture the observed readings, alarm states and any parameter changes so the maintenance record explains why TCP-LBF-IA1.36.IE.0 was accepted.
Purchasing brief
When asking for TCP-LBF-IA1.36.IE.0, include the entire type code, quantity, installation location, applicable approval, mating connector or board and required accessories. Ask a supplier to confirm the exact TCP-LBF-IA1.36.IE.0 designation in writing. A proposed equivalent must be checked independently for electrical behavior, mounting, software and certifications. The related codes below are search and identification references; they are not a declaration that they interchange with TCP-LBF-IA1.36.IE.0.
Related-looking designations
The following strings resemble TCP-LBF-IA1.36.IE.0 in the supplied product family. Their full suffixes may change function, ratings, mechanical fit or approval; consult each exact manufacturer's record before a substitute is used.
No additional same-pattern designation is grouped with TCP-LBF-IA1.36.IE.0 here. An alternate part still needs a separate exact-code check.
Close-out note
For future service of TCP-LBF-IA1.36.IE.0, retain the final wiring diagram, settings, test result and replacement reference together. Recheck the data for TCP-LBF-IA1.36.IE.0 if the connected controller, process conditions or regulatory setting changes. The table describes the named TCP-LBF-IA1.36.IE.0 where a value is stated; do not extend those values automatically to another listed code.
