Pepperl+Fuchs HIACA-UNI-FLK34-FLK34-1M0: function, connections and handover
Pepperl+Fuchs HIACA-UNI-FLK34-FLK34-1M0 is a HART connection cable selected to link a HART communication board with its termination board. The full HIACA-UNI-FLK34-FLK34-1M0 code is the identification anchor for this page. The shared main montage illustrates the Pepperl+Fuchs category and is not a photograph of this exact option. Before using HIACA-UNI-FLK34-FLK34-1M0 as a spare, compare the installed label and project drawing with the current manufacturer documentation.
Technical specification and identity
| Technical item | Verified value / selection note |
|---|---|
| Exact model | HIACA-UNI-FLK34-FLK34-1M0 |
| Product role | HART connection cable |
| Cable length | 1 m |
| Connector at each end | 34-pin female FLK |
| System | H-System HART connection |
| Temperature | -20 to 60 °C ambient |
| Variant check | Confirm the complete designation and current manufacturer documentation before replacement. |
Selection pathway
Start with the real duty of HIACA-UNI-FLK34-FLK34-1M0: link a HART communication board with its termination board. Then trace what connects to HIACA-UNI-FLK34-FLK34-1M0, including its power source, input or target, outgoing signal and mechanical support. Verify both 34-pin FLK sockets and the intended one-metre routing. Record the actual site settings and the parts that are supplied separately. This matters because a near-identical type string can conceal a different output, connection, dimension or approval.
Exact-code checkpoint: HIACA-UNI-FLK34-FLK34-1M0 must be confirmed against the fitted interface before substitution.
Installation and test
For installation of HIACA-UNI-FLK34-FLK34-1M0, document the existing assembly before disturbing it. Photograph the full label, terminals, cable exits, brackets and adjacent modules; mark conductors and save any controller or software configuration. Compare voltage, polarity, loading and environmental limits against the exact HIACA-UNI-FLK34-FLK34-1M0 technical record. If HIACA-UNI-FLK34-FLK34-1M0 is part of a safety or hazardous-area circuit, the site-approved design and certificates take precedence over an appearance match.
After fitting HIACA-UNI-FLK34-FLK34-1M0, prove its function in the completed system, not merely its power-on indication. Apply a known field condition, read the downstream controller or diagnostic tool, and repeat at both normal and limiting conditions. For HIACA-UNI-FLK34-FLK34-1M0, verify both 34-pin flk sockets and the intended one-metre routing. Capture the observed readings, alarm states and any parameter changes so the maintenance record explains why HIACA-UNI-FLK34-FLK34-1M0 was accepted.
Supply record
When asking for HIACA-UNI-FLK34-FLK34-1M0, include the entire type code, quantity, installation location, applicable approval, mating connector or board and required accessories. Ask a supplier to confirm the exact HIACA-UNI-FLK34-FLK34-1M0 designation in writing. A proposed equivalent must be checked independently for electrical behavior, mounting, software and certifications. The related codes below are search and identification references; they are not a declaration that they interchange with HIACA-UNI-FLK34-FLK34-1M0.
Related-looking designations
The following strings resemble HIACA-UNI-FLK34-FLK34-1M0 in the supplied product family. Their full suffixes may change function, ratings, mechanical fit or approval; consult each exact manufacturer's record before a substitute is used.
- HIACA-UNI-FLK34-FLK34-2M0
- HiACA-UNI-FLK34-FLK34-3M0
Close-out note
For future service of HIACA-UNI-FLK34-FLK34-1M0, retain the final wiring diagram, settings, test result and replacement reference together. Recheck the data for HIACA-UNI-FLK34-FLK34-1M0 if the connected controller, process conditions or regulatory setting changes. The table describes the named HIACA-UNI-FLK34-FLK34-1M0 where a value is stated; do not extend those values automatically to another listed code.
